HOW TO PAINT A GARAGE FLOOR

If your garage floor is feeling a bit old, grimy or just in need of a refresh, a new coat of epoxy—a hardworking specialty paint—will efficiently revitalize your garage floor. Painting your garage floor will also make it easier for you to clean.

A garage with gray floor and white walls, an assortment of ladders, cement, and a cabinet.


Ready to Paint Your Garage Floor?

The best way to paint a garage floor starts with checking to make sure your floor is in good condition.

If your garage floor has been previously painted or sealed, and there is no peeling, you’re good to go. However, if your garage floor is bare concrete, has peeling paint, has an existing high-gloss coating, or you see any moisture problems, it’s best to contact a professional painting contractor to get the job done right.

Step #1: Prep Your Space

How do you prep your garage floor for an epoxy paint? Creating a clean, tidy workspace is key. Step one for garage floor preparation before painting is to remove all items from your floor. Be sure to sweep the area just outside of your garage to prevent leaves and other debris from getting in while you’re working.

Consider weather when it comes to painting your garage floor: a warm, dry day is ideal for best results. The optimum climate is less than 70 percent humidity and no lower than 10° C (50° F).


Important
Safety Notes

Secure good ventilation in your garage: Open windows and keep the garage door open about 46 cm (18 inches) for proper air movement.

Wear rubber gloves and protective eyewear when mixing epoxy compounds.

Step #2: Clean Your Garage Floor

With everything off your garage floor, let’s look at how to clean your garage floor before painting. Start by sweeping and mopping the floor. Remove any grease stains by scrubbing with Corotech® Oil & Grease Emulsifier. Rinse the floor thoroughly with clean water and allow it to dry completely.

  • If you’re using Corotech® Oil & Grease Emulsifier to clean your floor, be sure to mix the concentrate with water before applying. Read all product instructions before use.

Step #3: Mix the Epoxy Primer

You should always prime your garage floor before you epoxy, as primer provides a solid foundation for your top coat. To prime your garage floor with Corotech® Moisture Tolerant Quick Set Epoxy Sealer, you’ll need to first mix the primer’s two components together. Pour Part B into Part A and use a drill mixer on a low setting for three to five minutes until completely blended. See the product’s Technical Data Sheet for detailed instructions.

  • Make sure the mixture is incorporated fully after first mixing by pouring the mixed material into another bucket and mixing again.

Step #4: Apply the Epoxy Primer

Once your epoxy primer is fully mixed, pour it onto your garage floor in a ribbon. Using a paintbrush, cut in the borders of your floor by applying the primer to the floor around the edges of the garage.

Switch to a squeegee or a roller to spread the primer onto the rest of the floor, working toward the exit of the garage so you don’t paint yourself in. Allow the primer to dry completely.

  • If you’re wondering how long to let your garage floor dry before you paint, Corotech® Moisture Tolerant Quick Set Epoxy Sealer has about a 4-hour dry time—depending on your environment. You should be working on a day that is below 70 percent humidity. If not, it could take up to 7 hours to dry completely.
  • You’ll know that the primer is dry because it will change from a milky white-yellow colour to clear.

Step #5: Mix the Top Coat

Mix your top coat according to the instructions on the can or the product’s Technical Data Sheet. When it comes to choosing your top coat:

Step #6: Apply the Top Coat

Just as you did with the epoxy primer, pour your top coat mixture down in a ribbon on the garage floor. Use a paintbrush to cut in your edges, and a roller to spread the epoxy throughout the rest of the floor. Remember to paint toward the exit of the garage.

Step #7: Add Optional Anti-Slip Aggregate and/or Garage Floor Flakes

Once you’ve applied your top coat, consider adding Corotech® Anti-Slip Aggregate, which creates a rough finish designed to elevate the foot or wheel on a damp or wet surface to help avoid slippage and hydroplaning.

  • Be exact about the quantity of anti-slip aggregate you use, as too much of it may make the floor hard to clean. Read all product instructions for recommended quantities and application.

You can also opt for INSL-X® Decorative Floor Flakes, which provide both an aesthetic look and help hide dirt.
  • Throw the garage floor flakes upward toward the ceiling as opposed to down on the floor for a more even distribution.

Step #8: Allow Your Garage Floor to Dry Completely

Allow 24 to 48 hours before you start returning items to the garage, and do so carefully. Make sure not to drag items back in place on your freshly painted garage floor. Wait seven to 10 days for your garage floor to fully cure before you drive on it.



Ask Your Retailer & Get More DIY Tips!

With your garage floor painted, why not try painting your garage door next? Visit your local Benjamin Moore retailer for help with all your painting needs. Find more tips in our How-To section.